千泰塑膠原料有限公司

TPV密封M2400NS ‖。TPV VX 5065UIX 、‖。PC 943-701 、→，TPU 127K 、PP H150L 、TPE S-50AFR 、‖。PP 3289M 、PP PHC27-90 、PP 7425 、LDPE LD185JD 、‖。PA66 FG173X31 PA/、‖。PC APEC 1800-700981 、→，PA6 ST811HS 、POM F20-73R1 、‖。POM 510GR 、PETG Z6018 、ABS VH-0850 、‖。PMMA D 1067 PA46 G2000E 、‖。PA12 3024GC6 、PC IFX3420Z 、PC OQ4005 、→，APAO 3315 、→，PEEK EP3140 、→，TPU 12H92E 、PP 11712 、PA6 2210G4 FNC1 、‖。TPE TF5TTT 、PC GR25 、→，PP 402-CB12 、PPS HZ1 、TPV 291-60B150 、‖。PP N4503 、‖。PC ML1665 、PC/ABS T45 PG 、→，EAA 20E482 、PC DE0069F 、→，PBT 5810G40 、TPU DP3690AU 、PC/ABS T85 XF 、PP AV161 、POM M270-12 、PBT 5300-2 、→，PP ERC161N 、→，PP P527K 、PC 9330-759 、‖。PP 401-CA55 、→，EAA 5200 、‖。PA46 TS200F10 、‖。POM AW-01 、→，PA6 K-FG0 、POM KFL-4036 、‖。PBT 6370 、LDPE 5004IM 、‖。PP ME212U 、→，PA6 GP1300A 、‖。TPU 540-4 、PA66 TSS 、‖。AS NF2200AF 、→，TPEE 1163D 、→，EVA P0803 、PA6 SX218V60 、→，LDPE N-11P 、‖。PC/ABS CY5210 、→，LLDPE L91507H 、PC KGN-15MRA 、LDPE C180BK 、PMMA BM-731 、‖。PP K7726H 、‖。PP MD000APH 、 TPV密封M2400NSOptical properties of PMMA 1, visible light: high transmittance of visible light. PMMA is the best polymer transparent material at present, and its visible light transmittance is 92%, which is [1] higher than that of glass. 1. ultraviolet light: quartz can be completely ultraviolet light, but the price is high, ordinary glass can only pass through 0.6% ultraviolet ray, but PMMA can pass through 73%. PMMA can't filter out ultraviolet (UV). Ultraviolet light penetrates PMMA, and part of the manufacturer [2] is coated on the surface of the PMMA to increase the effect and properties of the UV light. On the other hand, PMMA has better stability than polycarbonate in the condition of ultraviolet light irradiation. 2. infrared: PMMA allows infrared rays less than 2800nm wavelengths to pass through. Longer wavelengths of IR, less than 25000nm, are basically blocked. There is a special colored PMMA that allows a specific wavelength of IR to pass through and block visible light, (used for remote control?or?heat, etc.). The POM enhanced POM The main reinforcement materials are glass fiber, glass ball?or?carbon fiber, and glass fiber is most commonly used. The mechanical properties of the reinforced glass can be increased by 2~3 times and the hot deformation temperature is increased by 50 degrees?or?more. The high oil POM Adding graphite, F4, molybdenum disulfide, lubricating oil and low molecular weight PE to POM can improve its lubrication performance. For example, adding 5 copies of F4 in POM can reduce the friction factor by 60%, and increase the wear resistance by 1~2 times. In addition, the addition of liquid lubricating oil in POM can greatly improve the wear resistance and the limit of PV. In order to improve the dispersing effect of oil, the oil absorption carrier, such as carbon black, barium hydroxide, and ethylene propylene rubber, should be added. The friction of adding 5% oil POM is increased by 72%, and the limit PV can reach 3.9MPa m/s (pure POM is 0.213MPa m/s), which is 3~20 times that of other engineering plastics. PPO B has good electrical properties in a wide range of temperature and frequency. It has no hydrolysis and shrinkage, and has no self extinguishment. It is resistant to inorganic acid, alkali, aromatic hydrocarbon, halogenated hydrocarbon and oil. It is prone to swelling?or?stress cracking. C, it has the advantages of large rigidity, high heat resistance, refractory, high strength and so on. D and polyether have the advantages of wear-resistant, non-toxic, and resistant to pollution. Dielectric constant and dielectric loss of E and PPO plastic materials are among the smallest varieties in engineering plastics. They are hardly affected by temperature and humidity. They can be used in low, medium and high frequency electric fields. The load deformation temperature of F and PPO can reach more than 190 degrees C, and the embrittlement temperature is -170 C. G, its main shortcomings are poor melt fluidity and difficult processing.。